Showing posts with label masonry heater. Show all posts
Showing posts with label masonry heater. Show all posts

Sunday, September 30, 2018

Repairing the Masonry Heater Firebox

Last winter was the first for my masonry heater.  While building, curing and using it I meticulously followed all the proper procedures.  I used it full out, meaning firing it as often as recommended, simply because it was an abnormally cold winter and my farmhouse is unfinished.

I knew that the mortar was cracking inside the firebox, but put off repairing it as I was occupied with running the farm. A couple of weeks ago I began to consider what should be done.  After an inspection showed the mortar in the firebox was crumbling, I called Smith-Sharpe Firebrick Supply in Minneapolis and asked an expert "What should I do?". He said I might have used a bad bag of mortar, doubtful in my opinion, but that something called "Greepatch 421" would be the best product to repoint the joints.

When building the firebox I used the refractory mortar that came with the "kit" I bought from Eric Moshier at Solid Rock Masonry. It was rated up to 2500º. The new stuff is rated at 3500º. Maybe that will help, even though my temps never got above 2000º. (That infrared heat thermometer sure is useful.)

(Click on any picture to make it bigger.)


I started repairing the wall on the right. I scraped about 3/8" out of all the existing joints with a tuckpointing trowel. The mortar, when it didn't pop right out, was surprisingly soft.



 I also removed and relaid the floor of the firebox. The grate that fits in the hole seen in the bottom of the firebox was badly damaged and in need of replacement.  The "owners manual" from Solid Rock Masonry states that the grate will need to be replaced every other year. I'm ahead of schedule.

The old grate was badly corroded and had a bow/bend in it of about 1/2".

With the sides done I relaid the floor.
I think, and a phone call to the firebrick company will clear this up, that the mortar will have to cure for at least two weeks. Meaning no fires, and then only small ones. This is unfortunate because we've already had two nights with temps below freezing. For the next few weeks it looks like temps will be 10-15 degrees below normal.


Friday, November 17, 2017

Masonry Heater is Done

My friend Andy came up from Chicago to lay the fieldstone I'd picked and prepped around the masonry heater.



Next spring I plan on applying a clear sealer to the heater so the the colors - blues, greens, yellows, reds, white, oranges, browns - of the stones "pop". You can get a sense of what that will look like by simply spraying the stones with water, which I did in the photos below.

(Click on any of the photos to make them bigger.)

The firebox side, showing the clean stone.



How the stone looks when wet.




Oven side, dry clean stone.

Oven side, wet stone.
 All these stones were handpicked from our fields. Even after pressure washing them it wasn't obvious what they'd ultimately look like. I'm really happy with how it's turned out. Thanks Andy!



There's still one big test to come - Does it work? Early signs are promising, as there's a nice draft from the chimney.

We finished about a week ago, and the mortar still needs to cure for another 10 days until I can start curing it with a series of small fires.  That'll take another week. Meaning I can't really use it to heat the house for a few more weeks.

Wednesday, September 27, 2017

Masonry Heater Progress

 Some of the smaller rocks that we've picked were dumped near the house earlier this summer. They still have a bit of dirt on them, which I'm now cleaning with our balky pressure washer. The motor surges and eventually dies.

The internet has a solution, which has worked, somewhat.
The idle (pilot/lo) circuit in the carb is gummed up. What happens is when the engine achieves the desired rpm's, the governor closes the throttle. At small partial throttle, the engine must run on the idle/transition jets. Since they're obstructed by varnish, it starves for fuel. Rpm's drop, the throttle opens, the engine now draws from the less obstructed main jet, rpm's recover, throttle closes, repeat ad nauseum.

2 choices. Remove the "main jet" from the carb and clean it again (special attention to drillings along the side of the jet), and poke out the idle circuit while you're in there..... Or:

Add "Sea Foam" to the tank at double the recommended ratio on the bottle. The stuff is good at removing varnish, and in a little while the washer should be happy again.

----------------
















 I still have a lot to do on the heater. Finish up the core, another 6 courses, then put the downdraft channels on either side. Next would be building the clay chimney, which is routed through the 6 ft long bench and 9 ft up to the ceiling where it transitions to a double wall metal chimney and goes through the second floor and the attic/roof.

Finally, the whole core/bench gets clad with the field stone. 

I was hoping to get a little help from my friend Andy. I'm not sure if he'll be able to do so. In either case it'll be tough to get it done in the next month given all the other stuff that I need to do.

 Wikipedia has a good entry on Masonry Heaters if you want to learn more.